Have you bought an EdgeGuard Mini Spreader and trying to learn how to calibrate its settings? Look no further.
In this guide on EdgeGuard Mini Spreader Settings, I’ll be walking you through the efficient spreading techniques and calibration tips to help you achieve a dense and healthy lawn.
Calibration lies at the heart of achieving accurate and consistent spreading. By adjusting the settings of your EdgeGuard Mini Spreader, you can ensure that the right amount of material is spread out, thus avoiding waste and uneven coverage.
I will provide recommendations on adjusting EdgeGuard Mini spreader settings based on lawn size, allowing you to maximize coverage while minimizing effort.
Table of Contents
Understanding EdgeGuard Mini Spreader Settings
![EdgeGuard Mini Spreader Settings (Step-by-Step Guide) (1) EdgeGuard Mini Spreader Settings (Step-by-Step Guide) (1)](https://i0.wp.com/yardcurator.com/wp-content/uploads/2023/05/EdgeGuard-Mini-Spreader-Settings-Step-by-Step-Guide.webp)
Before going into the specifics of EdgeGuard Mini Spreader settings, it’s essential to understand how spreader settings work.
Spreader settings refer to the rate at which the spreader dispenses material, and they can vary depending on the type of material, the spreader’s make, and model, as well as environmental conditions such as wind speed and humidity.
The EdgeGuard Mini Spreader features a control panel that allows users to adjust the spreader settings to achieve a precise rate of application.
The spreader settings on this model range from 0 to 15, with the recommended settings listed on the back of the product package or in the product manual.
You need to calibrate your spreader before using it to ensure that the settings are accurate and consistent.
Also Read: Scotts Spreader Settings Conversion Chart – Complete Guide
Step-by-Step: Setting Up the EdgeGuard Mini Spreader
Follow these step-by-step instructions to calibrate your EdgeGuard Mini Spreader effectively:
1. Measure the Area
Start by selecting a specified area in your yard or garden that you can easily measure. This area should be representative of the larger area you plan to cover with the spreader.
2. Choose the Material
Select the material you intend to spread, whether it’s fertilizer, grass seed, or another granular product.
It’s important to use the same type of material during calibration that you will be spreading later.
3. Prepare the Spreader
Prepare your spreader by making sure that it is clean and free from any leftover materials. This will prevent contamination and incorrect calibration.
4. Fill the Hopper
Fill the spreader’s hopper with the chosen material. Be mindful of not overfilling the hopper to avoid jamming or uneven spreading.
The hopper is a container or reservoir located on the EdgeGuard Mini Spreader where the material to be spread is placed.
Also Read: Vigoro Spreader Settings – Tips to Achieve Better Results
5. Set Initial Spreader Setting
Set the spreader setting to a starting point, such as 5, to establish a baseline. This starting point will allow you to determine the spreading pattern and make adjustments as needed.
6. Spread the Material
Now, begin walking at a consistent pace, pushing the spreader across the measured area.
Make sure that you maintain a steady speed and avoid overlapping or skipping sections to obtain accurate results.
7. Measure Coverage
After spreading the material, measure the coverage area using a tape measure or any other reliable measuring tool. Calculate the actual coverage area in square feet or square meters.
8. Adjust Spreader Setting
Compare the measured coverage area with the expected coverage area.
If the actual coverage is less than desired, increase the spreader setting. If it exceeds the desired coverage, decrease the spreader setting.
Continue making adjustments until the actual coverage matches the expected coverage.
9. Repeat Calibration
It is recommended to perform the calibration process multiple times to ensure consistent results. This will help account for any variability or inconsistencies in the spreading process.
By following these calibration steps, you can fine-tune your EdgeGuard Mini Spreader’s settings to achieve accurate and efficient spreading.
Also Read: What’s the Right STA Green Spreader Settings?
EdgeGuard Mini Spreader Settings Based on Lawn Size
The size of your lawn plays a crucial role in determining the appropriate spreader settings for your EdgeGuard Mini Spreader.
Here are some general guidelines for selecting spreader settings based on lawn size:
1. Small Lawns
For lawns up to 1,000 square feet (93 square meters), it’s recommended to use lower spreader settings to achieve even coverage without wasting excessive material.
A spreader setting between 2 and 4 can often work well for small areas.
2. Medium-Sized Lawns
If you have a lawn between 1,000 and 5,000 square feet (93 and 465 square meters), mild spreader settings should be used.
Go for settings between 5 and 8 to ensure adequate coverage while minimizing the risk of over-application.
3. Large Lawns
For larger lawns exceeding 5,000 square feet (465 square meters), higher spreader settings are typically required to cover the expansive area.
Settings between 8 and 12 can help achieve efficient spreading while still maintaining uniform coverage.
Adjusting the EdgeGuard Feature
The EdgeGuard feature of the EdgeGuard Mini Spreader is a valuable addition that allows you to spread precisely along edges, borders, and other narrow areas.
On your spreader, you will find an EdgeGuard control mechanism.
This control lets you change the width of the spreading pattern, mainly along the spreader’s sides.
Before making any adjustments, evaluate the area where you will be spreading.
Determine if there are any areas or delicate plants that you want to avoid spreading material on.
Also Read: What are the Right Scotts Broadcast Spreader Settings?(2023)
Frequently Asked Questions (FAQs)
Can I disable the EdgeGuard feature?
Yes, the EdgeGuard Mini Spreader’s EdgeGuard feature can be turned off.
By adjusting the control mechanism to the right setting, you can open the EdgeGuard completely, allowing the material to spread evenly across the entire area.
This is useful when you want to cover larger areas without the need for precise edge control.
How do I know if the EdgeGuard feature is set correctly?
To ensure that the EdgeGuard feature is set correctly, you can perform a test spread on a small, controlled area.
Observe the spreading pattern and make adjustments to the EdgeGuard control as needed.
If the material is reaching beyond the desired area or not spreading far enough, you can fine-tune the EdgeGuard setting until you achieve the desired results.
Can I adjust the EdgeGuard feature during the spreading process?
Yes, you can make adjustments to the EdgeGuard feature while spreading.
If you notice that the material is reaching non-target areas or not spreading far enough, you can pause, adjust the EdgeGuard control, and continue spreading.
This flexibility allows you to adapt to different lawn layouts and customize your spreading pattern on the go.
Conclusion
Selecting the right EdgeGuard Mini Spreader settings and properly calibrating the spreader is crucial for achieving accurate and efficient spreading.
Adjusting the EdgeGuard feature allows for precise control and prevents material from reaching non-target areas.
By following these guidelines, you can optimize your spreading results, enhance lawn care efficiency, and maintain a beautiful and lush lawn.
Related Posts
- Scotts Wizz Spreader Settings Chart (Instructions and Settings List)
- Agri-Fab Spreader Settings Chart (Complete Guide)
- Vigoro Spreader Settings – Tips to Achieve Better Results
- Scotts Spreader Settings Conversion Chart – Complete Guide
- Lesco Spreader Settings (Achieving a Perfect Lawn)